Expert Answers about Fleetwood
- Does Install of Wheelmaster Inflation Kit on Inner Wheel Require Outer Wheel Removal
- It's going to be much easier to install the Wheelmasters # WM8004 on the inner wheel if you remove the outer wheel but if you had larger hand holes and maybe longer arms I could see it being possible.
When we installed it we pulled off the outer wheel though.
view full answer... - Can Two MaxxFan Dome Roof Vent Be Ran Off Single Switch
- Yes you could run two of the MaxxFan Dome Roof Vent w/ 12V Fan # MA00-03812B off of the same circuit to then be controlled with a single switch like # D16740.
view full answer... - How To Jump Start Battery Using Redarc In-Vehicle BCDC Battery Charger
- The Redarc In-Vehicle BCDC Battery Charger part # 331-BCDC1240D is a great option for charging a trailer battery. It sounds like you are concerned with the status of the starter battery and if that is case there is no need to worry as there are built-in safeguards to prevent puling power from the start battery when it gets below a certain voltage. If for some reason the start battery does die, you can use the auxiliary battery to jump start this with the Redarc Smart Start Battery Isolator...
view full answer... - Does the AirLift WirelessAIR Use Cell Service Signal?
- The Air Lift WirelessAIR Compressor System for Air Helper Springs # AL74000EZ uses Bluetooth to connect to the Air Lift LoadLifter 5000 Springs # AL88299. The antenna symbol you see on the screen indicates connection status or Bluetooth signal strength and not cell service strength.
Note that the system # AL88299 can only connect to one wireless controller at a time, whether it's your remote or the mobile app and will take about 30 seconds after disconnecting from one to pair with the other.
view full answer... - Can I Lift Vehicle Without Supporting Firestone Air Springs?
- When air bags are installed, you usually need to support the rear axle when the vehicle is hoisted. Now, Firestone is actually really proud of their air springs design since they use technology from their heavy truck Airide springs and these can withstand thousands of pounds of pulling force without damage.
As for the hardware, that's made to support the air springs. As long as they were installed correctly, they will be able to hold while the vehicle is lifted. Also, when you vehicle...
view full answer... - Brake Controller Installation in 2016 Toyota Tacoma
- To install the Tekonsha Prodigy P3 # 90195 in your 2016 Toyota Tacoma, you'll need the # 3031-P Brake Controller Wiring Adapter Harness. The connector you're looking for is located behind the kick panel where it meets the firewall as shown in the photos I've provided.
view full answer... - How Does Draw-Tite 2-1/2 Inch Trailer Hitch Install on a 1988 Ford F-250
- Drilling is required to install Draw-Tite trailer hitch # DT45502 on a 1988 Ford F-250. You will need to drill eight 1/2 inch holes to secure the hitch to the bottom of the vehicle frame. I have included a link to the installation instructions for you.
view full answer... - Where Does the Fascia have to be Trimmed on a 2016 Audi A4 to Install a Trailer Hitch
- Yes, fascia trimming is required to install Draw-Tite trailer hitch # DT24950 on a 2016 Audi A4. The area that needs to be trimmed is up underneath the vehicle and not visible otherwise. I have included a diagram that shows the area that needs to be trimmed. This is a bottom view as if you were lying on the ground looking up at the bottom of the vehicle.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated...
view full answer... - Is Drilling Required to Install Draw-Tite Front Mount Receiver on a 2015 Jeep Wrangler
- There is no drilling required to install Draw-Tite front mount receiver # 65069 on your 2015 Jeep Wrangler. I have included a link to the installation instructions so you can see the steps for installation.
view full answer... - Parts Needed To Install Brake Controller On 2008 Honda Odyssey
- I will be glad to help you out with that. You have the Primus Brake Controller, part # TK90160 so that is taken care of.
If you have a 4-way connector on your vehicle you will need the Universal Installation Kit for Trailer Brake Controller, part # ETBC7. This will connect to your 4-way connector and with additional wiring give you both a 4-way and a 7-way connector. I have attached a link to an installation video that shows a brake controller and the # ETBC7 controller being installed...
view full answer... - Brake Control Connector Location on 2015 Ford Expedition
- The information I have on the 2015 Expedition brake controller connector location isn't complete. I know the connector is located under the dash behind the center console, closer to the passenger side but I don't know the easiest way to access it. My Tekonsha representative send me a copy of a photo he found that shows where the connector is located, but there isn't enough detail in the photo to tell how to get to it.
Judging by what I could make out, your best bet would be to remove the...
view full answer... - Brake Controller Connector Location 2015 Ford Expedition
- The information I have on the 2015 Expedition brake controller connector location is pretty sketchy. I know it's located under the dash behind the center console, closer to the passenger side but I don't know the easiest way to access it. My Tekonsha representative sent me a copy of a photo he found that shows where the connector is located, but there isn't enough detail in the photo to tell how to get to it.
Judging by what I could make out, your best bet would be to remove the glove...
view full answer... - Do Hitch Extenders Cut the Capacity of Trailer Hitch by 50 Percent
- When you use a hitch extender you will end up reducing the capacity of the vehicle by 50 percent like you mentioned. So your vehicle that has a 2,000 lb capacity would then be reduced to 1,000 lbs total trailer weight and 100 lbs tongue weight.
I attached a help article on hitch extenders for you to check out as well.
view full answer... - Troubleshooting No Power to 4-Way on 2014 Lexus RX 350 After Curt Harness 56083 Install
- The only way to know for certain is to contact at Lexus dealer with your VIN to determine if you have the tow package. Sounds like you are missing some relays or fuses under the hood of your 2014 Lexus RX 350 that will allow the trailer wiring harness to be active.
There is a tech note for this harness that it may require additional components such as relays or fuses depending on how the vehicle is equipped.
view full answer... - Can Utility Lights in Trailer Run Off Running Light Circuit Through a Switch on an Aluminum Trailer
- Yes, you can run the switch power wire to a clearance light but the trailer would have to be connected to the vehicle with the running lights on for the interior lights to have power.
Aluminum does not offer the best ground so if the lights do not work you may have to run a jumper ground wire to a steel component or the main trailer connector ground. I would try it first to see if there is any problem with grounding to the aluminum surface.
A fuse is not needed though you could add one...
view full answer... - Does the Hanger Kit part # APT3HD Get Welded or Bolted to Trailer Frame
- Suspension hangers like what come with the Hanger Kit part # APT3HD that you referenced are designed to be welded to the trailer. You would not want to bolt this kit to the frame of your trailer.
view full answer... - Recommended Gooseneck Hitch for a 2013 Ram 2500 Power Wagon
- You are correct the beds on the power wagons are a little bit shorter than standard on the 2013 Ram 2500's. To add a gooseneck hitch you will want the B&W Turnoverball Underbed item # BWGNRK1308. This hitch is custom fit and bolts to your Ram with included hardware.
I checked with B&W and there is some variance on whether or not you have to modify the bracket on one side and drill into the other for the power wagons. On the driver's side bracket there is a little piece that you'll need...
view full answer... - Does the Multi-Purpose Access Door Come with a Lock
- The Multi-Purpose Access Door part # SE98VR does not have a lock nor is it offered with one available. That said, I'm sure you could modify and add a lock such as the Camco Cam Lock part # CAM44293 for security. I will be honest with you though, it's a plastic door so if anyone really wanted to get what was inside it would not be very difficult.
view full answer... - How to Locate an Installer For the Custom Third Brake Light Camera # 3460003
- Just below the images and videos you will find a link "Locate installers near me" which will help you locate an installer near your zip code for the Custom Third Brake Light Camera # 3460003.
view full answer... - How to Change Monitor Settings of Hopkins Smart Hitch Backup Camera HM50002
- There isn't much you can change on the monitor of the Hopkins Smart Hitch Backup Camera and Hitch Aligner System part # HM50002 but if you press the IN button you can use the up and down buttons to toggle between hitch mode and everyday mode. You can see more info on this in the attached install instructions link as well as review video link.
Pressing the IN button also allows you to toggle between various color and brightness settings as well.
view full answer...
Go To Results